Do not underestimate the forklift at the office. If the procedure is bad, there will certainly be serious mishaps in minutes, and there are lots of mishaps including forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, leading to a moving mishap.
Situation 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift freight goes beyond the allowed width of the path and hangs on the roadside rack, which virtually creates an crash.
Situation 4: Forklift is speeding and rolls over during a turn.
Instance 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these matters ：.

Begin.
1. Before beginning, observe the surroundings, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free before beginning.
3. When the forklift starts with a tons, the driver needs to first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole ought to be slanted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job website or while driving, be careful that there will be no barriers in the sky. When the tons is taking a trip, the fork must not be increased too high, which will influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal ought to be provided initially. High-speed sharp turns are forbidden. High-speed doglegs will cause the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake all of a sudden while driving with tons unless there are unique circumstances.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a certain safety distance from the car ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the tons need to not obstruct the motorist's view. In unique scenarios, when the thing influences the forward vision, drive at a reduced rate when turning around.
9. It is restricted to activate the ramp, neither to drive throughout the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility location is 5 km/h, and it has to drive securely at a reduced rate when going into the manufacturing workshop area. .
11. When the forklift is lifted, lifted or driven, it is forbidden for workers to base on the fork to hold products and play a balancing role. .
12. If problems are found, they will certainly be fixed and reported in a timely manner, and they will certainly never ever operate with illnesses or hide them.

filling and discharging.
1. When fork-loading products, the range in between the two forks should be readjusted as required to make the tons of both forks well balanced and not skewed, and one side of the item need to protest the rack. .
2. It is restricted to work with a solitary fork or utilize a fork top or pull. In unique situations, safety indication need to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift has to be stopped with the brake. .
4. The rate of the automobile ought to be slow and steady. Take care not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure individuals. .
5. When utilizing a fork to fork the goods, the fork Stand-on Electric Pallet Stacker should be as deep as feasible under the tons, and it should be kept in mind that the fork suggestion should not touch various other goods or objects. The lots should be maintained with very little back tilt of the gantry so that the load does not move in reverse. The pole can be tilted ahead a little when the tons is decreased to allow for very easy positioning of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm individuals. .
8. Overloading is forbidden, and it is banned to make use of forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to Electric Forklift Truck for Warehouse slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Before leaving the forklift, you must unload the goods or lower the fork framework.
2. Draw the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is turned off and the power is removed. (Except for unique circumstances, such as the driver does not leave the car's line of sight and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water ought to be added.
2. Check the safety and security efficiency of beginning, running and braking.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are normal.
5. After the forklift is running, the exterior leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be as well sharp to stop the propensity of " totally free switching";.
6. Running up and down the slope must be slow and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is more than 10%, the car should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to lift the goods for far away driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Parking is not permitted under the following problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the very same size as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844